NStor Technologies Disk Array Enclosure User Manual Page 59
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Using the CR8e
Options Menu
47
4 Use the up/down arrow buttons to make your SCSI ID group selection and
press the Enter button.
Note the flashing set of IDs, if present. These will be the group currently
configured.
5 Press the Escape button twice or the Menu button to return to the Main “Status
OK” screen, then power cycle the host computer and CR8e subsystem.
NOTE:
You must power cycle the subsystem for the SCSI IDs changes to take
effect.
To change the SAF-TE card SCSI ID, follow the five steps above, except select “Set
SAFTE ID” in step 3 and choose from “Set ID on Lower Bus” or “Set ID on
Upper Bus” in step 4. Use the up/down arrow buttons to change the ID value.
Since the subsystem is available in either a split SCSI bus design or as a single
SCSI bus, you can set the SAF-TE card SCSI ID for each bus if a conflict is
occurring. The default setting is SCSI ID 3 for each bus. The setting for SCSI
ID “OB” indicates Off Bus and is generally used when the subsystem is
installed in a “Slave” subsystem in a Master/Slave environment.
MENU ENTER ESCAPE
nStor
RESET DEFAULT IDS
SET UPPER SLOT IDS
SET LOWER SLOT IDS
SET SAFTE ID
MENU ENTER ESCAPE
0 1 2 3
0 1 2 4LOWER 4
4 5 6 7
4 5 6 8
5 6 7 8
nStor
MENU ENTER ESCAPE
SET ID ON UPPER BUS
SET ID ON LOWER BUS
nStor
MENU ENTER ESCAPE
ENTER TO SET NEW ID
ESC TO EXIT
PROCESSOR ID: 3
ARROWS CHANGE ID
nStor
- Regulatory Information 3
- Power Cord Selection 4
- Contents 5
- Features 10
- Where to Find Answers 11
- Registering Your Product 12
- Getting Started 13
- CR8e Subsystem at a Glance 14
- Components 16
- I/O Interface Card 18
- Power Cord Connector and Fuse 18
- Configuration Modules 19
- Controlling and Monitoring 20
- Power-On LED 21
- Status Indicator LEDs 21
- Status LEDs 22
- Activity LEDs 22
- Alarm Speaker 23
- Fault LEDs 23
- SAF-TE Card 23
- Installation 25
- System Requirements 26
- Guidelines 26
- Rack-Mount Subsystem Assembly 27
- Component Installation 29
- Cabling Configuration 32
- Termination 33
- Ultra Wide SCSI Mode 34
- Single-Bus Enclosure 36
- Fast Wide SCSI Mode 38
- Two Dual-Bus Enclosures 40
- Two Single-Bus Enclosures 44
- Other Configurations 48
- Using the CR8e 49
- Firmware Error Conditions 50
- SAF-TE LED Matrix 51
- Operator Control Panel 52
- Power Supply Error Conditions 53
- Subsystem Status Icon 53
- Main Menu 54
- POST Results 56
- Internal Temp 57
- Options Menu 58
- Reset Default IDs Selection 60
- Heat Threshold 61
- SAFTE CHAIN ID 62
- Change Passcode 63
- OPTIONS WILL REMAIN 64
- UNLOCKED UNTIL YOU 64
- RETURN TO THE 64
- DEFAULT SCREEN 64
- Troubleshooting 65
- Common SCSI Bus Problems 66
- Maintenance 69
- Replacing a Power Supply 70
- Replacing the Cooling Fans 72
- Thumb Screw 73
- Replacing a Fuse 74
- Replacing the CR8e Cabinet 75
- Glossary 77
- Technical Information 81
- CONNECTORS AND JUMPERS 82
- JP3 (SCSI-to-SCSI IDs) 85
- JP4 (SCSI ID Settings) 86
- JP5 (SCA Remote/Delay start) 87
- J15 (FAN) and J17 (OEM FAN) 88
Haier Split Type Room Air Conditioner No. 0010551809 manuels
Manuels d'utilisation et guides de l'utilisateur pour Climatiseurs à système divisé Haier Split Type Room Air Conditioner No. 0010551809.
Nous fournissons des manuels en pdf 1 Haier Split Type Room Air Conditioner No. 0010551809 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comments to this Manuals